Accessories

You are compiling your personal development environment?

Sometimes its hard to get certain components in small quantities.

The following pages contain parts to help you reach your goals faster.

PCBs

LabCard CentiPadLK105

Description:

You need to test components for your custom application with CentiPad?

The LabCard might be the ideal workbase for you. In Europaformat (160mm x 100mm) the CentiPadLK105 combines essential interfaces like Ethernet, USB and RS232 with a big through hole matrix. A special feature are the SMD-Pads in various sizes on both PCB sides below the CentiPad-connector, which greatly facilitate testing of SMD-components. As any good laboratory card the LabCard features a VG-connector to other devices.

CentiBOB-Card CentiBOB104

Description:

Surely you know CentiBOB104 from our DevKits.

Thanks to its amble interfaces, you can thoroughly test CentiPad with the CentiBOB.

If CentiBOB is configured with components needed by your actual application, CP-BOB200 is a cost saving, reliable and tested alternative for pre- and small series in comparison to customer designed boards.

Wide selction of interfaces:

• Ethernet
• 2x RS232 Schnittstelle configurable via solder jumpers)
• USB Host interface
• USB Device interface
• CAN Interface edge connector
• 1wire Interface pad for 1wire sensors
• IrDa (optional)
• IR-Remote-Control LED (optional)
• I2C-interface via standard Mini-DIN 6pol jack (optional)
• I2C 8pol DIL IC-pad
• SPI interface edge connector
• LCD-interface for a various alphanumeric and graphic dot matrix LCD’s
• Sound:
• 3,5mm Stereo LineIn
• 3,5mm Mono MicIn
• 3,5mm Stereo LineOut
• 3,5mm Stereo Headphone
• fixed memory interface
• ATA40, 3,5“ harddisk
• ATA44, 2,5“ harddisk (optional)
• CompactFlash interface (optional)
• SD/MMC (optional)
• SoftOn- and Reset-button
• 7 open-collector-power-outputs (GPIO0..5 und PCK0)
• switched power supply with 7..28V input range and maximum 1,5A output @ 5V

Prototype card CentiPadPT101

Description:

Die Prototypenkarte CentiPadPT101 mit passendem Gehäuse [link] und Zubehörset [link] eignet sich hervorragend für Kleinstserien z.B. im Prüfmittelbau. Die Platine kann je nach Bedarf mit verschiedenen Steckern bestückt werden.

Funktionsumfang CentiPadPT101:

• Trägerplatine für CentiPad, passend zum Einbau in Aluminiumgehäuse
• Lötpunkte für LAN-Buchse
• Lötpunkte für Spannungsversorgungsbuchse
• Lötpunkte für USB-B-Buchse
• Lötpunkte für SubD25-Stecker/Buchse
• Lochrasterfeld

Prototypenkarte CentiPadPT201

Description:

The prototype card CentiPadPT201 with matched housing [Alubos] and accessories is ideal for small series, e.g. customized test equipment building. The PCB can be fitted with various different connectors.

Features CentiPadPT201:

• carrier board for CentiPad, fitting into Alubos aluminium housing
• pad for LAN-connector
• pad for power supply connector
• pad for switched regulator
• pad forUSB-B-connector
• pad for SMD-parts
• hole matrix

Accessory parts

This page lists parts used in connection with CentiPad. Simply order using part number at info@centipad.com.

accessory kit 1

The accessory kit contains parts for building your own labcards.  Das Zubehörset enthält typische beim Aufbau eigener Laborkarten benötigte Bauteile. Parts are losely packed in a small plastic bag. accessory kit 1 contains:

1x LU1T041F-43

2x SL 2X36G 2,54

accessory kit PT1

This accessory kit contains parts for the prototype card PT1

• USB-B
• LAN-connector/transformer
• 2x36 connector for CentiPad
• power supply connector

accessory kit PT2

This accessory kit contains parts for the prototype card PT2

• USB-B
• LAN-connector/transformer
• 2x36 connector for CentiPad
• parts for switch power regulator

LAN-connector/transformer combination

Description:  RJ45 Connector Module with intergrated 10/100 Base-TX transformer and LED’s. This cost effective and small module is used on CentiBOB.

part number: LU1T041F-43

Datasheet: lu1t041f-43(m)-reva2.pdf

LAN-Transformer

description:  SMD 10/100 Base-TX Pulse-transformer matching CentiPads PHY.

part number: TS6121C

Datasheet: TS6121C_Series.pdf

Connectors

Description: These 2x36 Pin connectors with 2,54mm raster are the counterparts ofCentiPads connectors.

part number: SL 2X36G 2,54

Datasheet: -

Connectors (female)

Description: These 2x36 Pin female connectors with 2,54mm raster are fitted on CentiPad. CentiPads without connectors can be retrofitted with those.

part number: BL 2X36G 2,54

Datasheet: -

power connector for PT

Description:  power supply connector for PT101/201

part number: -

Datasheet: -

USB-connector

Description:  USB-buchse für PT101/201

part number: -

Datasheet: -

Connectors

All connectors used on the CentiBOB can be optained from us. (delivery time quantity dependant, please request)

Housing

Housing for CentiPadPT101

The PCB CentiPadPT101 is developed for the ALUBOS 800-150 housing by Bopla. A complete housing consists of one aluminium profile part and two caps. We will gladly finish the parts to your demands [Services]

ABD 800  standard aluminium cap for ABPH 800

ABM 800 AL-BE  cap with 9V-block battery holder for ALUBOS 800

ABPH 800-150 aluminium housing for CentiPadPT101

Housing for CentiPadPT201

Te PCB CentiPadPT201 is developed for the ALUBOS 1000-200 housing by Bopla. A complete housing consists of one aluminium profile part and two caps. We will gladly finish the parts to your demands [Services]

ABD 1000 standard aluminium cap for ABPH 1000

ABM 1000 AL-BE cap with 9V-block battery holder for ALUBOS 1000

ABPH 1000-200 aluminium housing for CentiPadPT201

copyright 2007 - www.centipad.de - all rights reserved